Section 8 - Cable Specs



OK OK OK.  Here are the cable specs.  They are 100% correct.  Of course I
wouldn't know because these are for information purposes only.  I have been
told however by VERY reliable sources that they are guaranteed, 100%, GRADE-A,
correct.  If they don't work for you, you did something wrong.


Cable Instructions for the bag phones (thanks Jakey) phone (female 25 pin) computer (male 25 pin) (parallel port) 18 ----------------------- 1 21 ----------------------- 2 1 ------------------------ 4 Below are 10K ohm resistors 12 ----------------------- 12 ----/\/\/----. 11 ----------------------- 13 ----/\/\/----+ 4,5,8 -------------------------------------' 2,3,17,20----------------- 18 --- Ground/black wire (-12 Volts) 16 ------------------------------ Positive/yellow wire (+12 volts) By the way, Jakey told me to remind you that the handset can NOT be plugged in while this cable is hooked up.
Motorola Cellphone cable construction for flips ------------------------------------- DB25 FLIP Battery Eliminator cable ---- ---- attachment pins up: 1(--------)4 --------= 2(--|<----)Jump this line to the Center 1 = Pin on the back of phone. --------= = 4(--|<----)1 "|<" is the IN4001 diode. --------= = 12(--------)5 --------= 4 = -->To phone 13(--------)6 --------= 5 = 18-25(-+------)8 --------= | 6 = | +-)7 --------= | | 7* = | | --------= | | 8* = NeG PoS ---Cig adapter --------= DB25 Male Phone Power Connector (see Note 1) 1-To phone pin 4 1-DB25 pin 4(see note 2) Gnd-To Db25 Pins 18-25 and 2-To Phone test lead 2-NC Phone pin 8 (see note 2) 3-NC 3-NC Tip-To phone pin 7 4-To phone pin 1 4-To DB25 pin 1 (see note 2) 5-NC 5-To DB25 pin 12 6-NC 6-To DB25 pin 13 7-NC 7-To tip on power connector 8-NC 8-GND 9-NC Test Lead-To DB25 pin 2 (See note 2) 10-NC 11-NC 12-To Phone pin 5 13-To Phone pin 6 14-NC 15-NC 16-NC 17-NC 18-GND \ 19-GND | 20-GND | 21-GND |--Conn together to GND on 12v conn 22-GND | And pin 8 on phone plug 23-GND | 24-GND | 25-GND / NOTE 1: The power adapter on the cable is 12 volt input but is a regulated 7.95 volts out. DO NOT connect 12 volts between pins 7 and 8 on the phone connector. NOTE 2: | /| DB25 Pin 4-----| < |------Phone pin 1 | \| | /| DB25 Pin 2-----| < |------Phone test lead | \|
Motorola Transceivers _____________________ 4500x,4800x,6800x,Etc. ______________________ Female 25 Pin Male 25 Pin D-Connector D-connector To transceiver To P.C. Parallel Port Pin Pin 1._____________________________________ 4. 2._____________________________________ 18. ___10k______ 13. / ______4+5._______________________/____10K______ 12. | 12.____________________________________/ | 11._____________________________________ 13. | 18._____________________________________ 1. | 21._____________________________________ 2. | ___14+17+20+23.____________________________ 18. | | | |___ -ve | |________ +ve 9 Volt
Motorola 8500x 8800x(early type) ________________________________ 25 Pin D-plug(P.C.lpt1) Phone Back(battery removed) Pin Diodes 3.--orange-|

Previous - Motorola Bible: Phone Pinouts
Next - Motorola Bible: Trik Clip
Y'know, if you log in, you can write something here, or contact authors directly on the site. Create a New User if you don't already have an account.